Language:
Currency:
VAT Mode:
Categories
Newsletter
To receive valuable information, subscriber only discounts and new product announcements:
*Email:
First Name:
Last Name:
* required
Manufacturers
Help & Info

Tri Electronics - Diamond Wizard Electronic Diamond Moissanite Tester

OPERATING INSTRUCTIONS

Diamond Wizard is a unique high technology professional digital instrument where all of its operations are controlled by microprocessor with latest computerized, superior surface mount technology featuring fast start-up and instant recovery for a test. This device separates real Diamonds from traditional Simulants and Moissanite. Diamond Wizard is equipped with super bright light that illuminate loose diamonds for grading in the raw. If the operator of this instrument does not carefully follow the instructions listed below the end result might be incorrect operation and misleading test result.

  • To begin operation: Remove protective snap-on cap from the sensor end of the tester to expose the sensor tip. Slide “On/Off” switch to the "On" position. The unit responds with a brief beep and the red "Ready" light starts blinking indicating that the device is getting ready for operation. When the "Ready" light stops blinking and stays on the device is ready to be used.
  • Testing for Diamond, traditional Simulant and Moissanite: gently press and keep the tip on the stone until the audible "click" heard. When the test is complete the signal automatically goes to appropriate light accompanied by a distinctive beep, and no further testing is required.
    • If the stone is a Diamond the green "Diamond" light will illuminate
    • If the stone is a Simulant the yellow "Simulant" light will illuminate.*
    • If the stone is a Moissanite the "Moissanite" light will illuminate.
    • If there is metal the "Metal" light will illuminate.
    • If test is not complete the ready light will blink a few times then returns to the on position.
  • When testing the stone, be sure you placing your thumb finger on the metal label in the front side of the device to prevent false indication. The sensor tip must be in contact with the stone only (not metal) for accurate test.

    *Note: To identify CZ and certain other low grade simulants with "Simulant" light and associated sound the sensing tip should be pressed against the stone in such a way that the audible click should be heard. Otherwise no indications will take place.
  • For grading and visual gem inspection activate the super bright light be pressing the push button switch located on the top of the unit. The light will illuminate the loose diamonds. The diamonds should be placed on the diamond paper for grading in the raw. To turn light off press the pushbutton switch once more.
  • Important note: Certain types of Moissanite stones have an electrical conductivity comparable to metal. Please follow these guidelines: if the test is being performed and the sensor tip has contact only with the stone and the "Metal" indication light comes on, the stone must be a Moissanite. To be sure that the stone is a Moissanite repeat the test on metal and the stone again.

    Turnoff: Slide the On/Off switch To "OFF' position, and store until next use.
    If the instrument left turned on for more than (4) minutes it will automatically shut itself off and audible sound will sound every 10-seconds indicating that the On-Off switch needs to be returned to "OFF' position.
  • Operating temperature: This tester can operate in hot and relatively cold environment from 60F (15C) to more than 100F (40C).
  • Cleaning: The sensing tip on the Diamond Wizard will need to be cleaned regularly. To clean depress and rub the tip on a piece of white bond paper or sand paper. If necessary scrape it with a fine needle file.
  • Loose Stones: The instrument kit contains a small metal plate for testing loose stones. Place the stone table face upon the metal plate and test You will not obtain the readings with the plate unless you hold the plate with your other bare hand.
  • Power source. The Diamond Wizard equipped with brand name "AAA" alkaline batteries for continuous work of 4-6 hrs. When there is no sound following the unit’s turn on and the "Ready" light blinks nonstop it indicates that the battery is low. The device must be turned "OFF" and the batteries replaced. Operating the Diamond Wizard with low batteries could result in false readings.
  • Optional power source: In addition to "AAA" alkaline batteries the unit will operate with optional AC/DC converter available either from our authorized distributor or directly from TRI Electronics Inc.

FEATURES

    • Fast start up
    • Instant test recovery
    • Recognize any size and any resistance of mossanite stones
    • No false Moissanite reading on small diamonds
    • Positively identifies Diamond, Simulant and Moissanite
    • Tester can operate in hot and relatively cold environment from 60F (+15C) to more than 100F (40C)
    • Equipped with three AAA batteries for continuous operation for up to 6 hours.
    • Automatic shut off
    • Metal detector
    • Audible beep will sound when test is complete
    • Equipped with super bright light for grading the stones

SERVICE

If there are any questions or problems regarding Diamond Wizard operation please contact our service department by phone 1-858-571-4881 or Fax 1-858-571-5404. Most of the problems can be easily and efficiently resolved over the phone. At your preference you can contact us via e-mail service@trielectronics.com or write:
Tri Electronics Inc. 9570 Ridgehaven Court Ste "A" San Diego, CA 92123.

WARRANTY

Tri Electronics Inc., as the manufacturer of the Diamond Wizard tester, believes the instrument will provide a fast and reliable test which will determine the authenticity of diamonds when used in strict accordance with the provided instructions.
Tri Electronics Inc. warrants that each instrument is free from defects in material and workmanship for a period of three (3) years from the date of purchase.
This warranty applies to a Diamond Wizard tester that is not abused or improperly used and only if the device is used in accordance with the Owner's Manual furnished by Tri Electronics Inc.
This warranty does not cover: any product where an attempt to disassemble the same is established; modifications; alteration; unauthorized repair or service of the product or damages or defects resulting from accident or any events beyond the control of Tri Electronics Inc.
The warranty is offered to the original purchaser only and proof of purchase is required for the warranty to be effective. Batteries are excluded from the warranty.

WARNING TO PURCHASER

Upon purchase of this instrument the purchaser, their assigns or any other user of this instrument understands and accepts the fact that Tri Electronics has no control over the use or condition of the tester in operation nor does Tri Electronics have full or complete access to or current or complete knowledge of unique synthetic stones, grown stones, or new chemical alterations of manmade gem stones.
It is, further, expected that the purchaser, their assigns or any other user of this instrument is knowledgeable of gem stones and understands their obligation to conduct traditional or special alternate test on suspicious gemstones to protect their interests. Based on these conditions, which are clearly understood to be beyond the control of Tri Electronics, the purchaser, their assigns or any other user of this instrument agrees upon purchase or use of the instrument to waive any right to legal actions against Tri Electronics resulting from erroneous tests in excess of the value of the tester.